With a thin straightedge in the bottom of the slot and resting against the second fret, there should be minimal clearance over the first fret. 5.0 out of 5 stars 9. I shoot for twelve thousandths (0.012) of an inch clearance under the G and D, and ten thousandths (0.010) under the A and E. You’re all done. (You'll probably be doing this after you learn to make a nut, because you'll get hooked on setup work just like I did!). Once you have your relief dialed in, you can move on to the adjustments at the bridge. String Height (measures top of fret to bottom of string): Bass-side string height at 12th fret: 3/32" Treble-side string height at 12th fret: 2/32" Relief (measures distance from top of fret to bottom of string while fretting the 1st and 15th fret): Relief at 5th Fret: .005" (a post-it note folded in half is about .005") We consider these measurements to be a "medium" action height. String gauge will have a huge effect on the feel and playability of your mandolin, with lighter gauge strings being easier to fret than heavier gauge strings. Don't make a new nut just to fix a low slot—fill it! I'm always afraid I'll take too much from the E string slot. After you have selected your string gauge, neck relief will be the first thing to check. I can't put my finger on it yet (no pun intended) but I think both the spacing between courses and the space between strings on the same course is not what I'm used to. If the fretted note is not in tune with the open string, you adjust it by: Every note may not be perfect, but with a compensated bridge top, they should be very close. "On the journey to excellence, enjoy mediocrity! Now go try that Grisman tune again. Action is a term frequently used to describe the height of the strings above the frets and an instruments playability. I don't ever measure the first fret, but at the 12th fret I usually go for 4-6/64th's on the G course and 2-3/64th on the E course (depending on the player's playing style). Finally, pencil-in the approximate shape of the nut when viewed end-on from the bass or treble side. A poorly setup mandolin is brutal to play, but one that’s setup correctly is a joy. thanks, dave..... but to me, mandolins are a little touchier than guitars.....i've noticed that if the bridge is lowered, tone and volume diminish.....which i don't want.... how hard is it to install the fixed jack on the mando K&K???? I know they are not the best sounding or best built instruments but I am personally infatuated with the design (shape) and would love one for my meager lower end collection. Adjusting bridge height using thumb wheels, Measuring Gap between strings and first fret using a feeler gauge. I like my action low and I play in an acoustic/folk/indie band. One to two thousandths (.001) of an inch, measured at the sixth fret, with the string fretted at the first and twelfth, works well for most players. In practice, I've found that there are some musicians whose playing attack is so vigorous that they require the nut to be higher to avoid the open string buzz. An Unofficial forum for those who love Martin instruments - Founded by Steve Stallings. That gives us smooth accurate tuning. If the strings are too low, they will buzz when played open. Learn About Guitar Nut + Saddle Setup + Repair, Find the proper fret position with the official Stewart-MacDonald Fret Calculator, Stewart-MacDonald is PCI compliant and validated for secure e-commerce. If the straightedge rocks on the first fret, it means that the slot is too low. and string height at the bridge? Oops, looks like you forgot something. thanks a lot bryan....do you happen to know what the 1st fret action is? On mine, I set the relief as flat as possible, the nut action the same method as guitar (Frank Ford's Frets.com) & just lower the bridge/saddle until it's comfy & doesn't buzz. Learn more about mandolins and find recommendations. The string height actually gets slightly lower at the first fret (and other frets) as that happens through playing... That is why I check the nut height with a straightedge, instead of relying on the string alone. If the strings are too high at the nut, it’s really tough to fret, and the intonation in the first position can be sharp. Over time certain elements can affect the action of a mandolin, making it harder to play or degrading the quality of sound and clarity. I use Fret End Nippers to squeeze the split nut together, but a pair of pliers will do. •   No matter how many orders you place. Intonation is the adjustment that allows the fretted notes to play in tune with the open string. Adjust the truss rod We’ll go through each, and have a look at how they are interrelated. To me its appeal is in its shape and if it doesn't sound so hot,,, thats OK with me. I will go back through the Frets.com site and refresh my memory. moving the bridge towards the neck if the fretted note is flat, moving the bridge away from the neck if the fretted note is sharp. The top of your bridge sits on those wheels, which move up or down when you turn them, raising or lowering the action. - The string height in the nut is the same as the fret height above the fingerboard (some like them very slightly higher). Disclaimer Section: IMHO, YMMV, IMHE, Don't Try This At Home, Take With Grain Of Salt, etc, etc. 12th fret slightly over 1/32 on the E and 2/32 on the G. With a good fret level this seems to work well for me. Jan-23-2010, 9:54am #7. thejamdolinplayer. Save on Over 900 Items. and thanks to you too....i believe i'm good to go now..... get the nut right and then use the wheels for your attack. Black Friday Sale! In order to make adjustments to the action of the nut, you will need a set of files, one that coincides with the width of each string rut in the nut, a feeler gauge, a tuner, and some time and a whole lot of patience. General String Height - Action / Set up / Style Survey, Today only, November 26 - 40% off all Mel Bay titles with Discount Code THANKS, http://www.youtube.com/user/TheJamdolinPlayer, Jams, Workshops, Camps, Places To Meet Others, Technique, Theory, Playing Tips and Tricks, Bluegrass, Newgrass, Country, Gospel Variants, Old-Time, Roots, Early Country, Cajun, Tex-Mex, Jazz/Blues Variants, Bossa, Choro, Klezmer, Celtic, U.K., Nordic, Quebecois, European Folk, Orchestral, Classical, Italian, Medieval, Renaissance, Octaves, Zouks, Citterns, Tenors and Electrics, If this is your first visit, be sure to With this in mind, if you rest a straight edge across the strings, just in front of the bridge, all eight strings should touch the straightedge, with no high or low strings. The improved version of the classic Fender Strat Bridge, The most consistent, top quality Strat® replacement body on the market today. Relief is needed to make space for the oscillation of the string, which is greatest at its mid-point. The bridge height adjusts the action, or the height of the strings above the frets. I like the string height at the first fret to be the same or slightly less as it is when i fret the first fret and look at the height between the string and the fret at the second fret. Last bridge adjustment: intonation. Any lower on the G and buzz is likely but after a bit of use, the E could be brought down a bit though I don't recommend it. Your purchases help youth music programs get the gear they need to make music. Thank you for the reply's. i'm leaning toward the carpenter jack for that reason... Dave's taken the words right out of my wireless keyboard - it's never occurred to me either! Scrape, cut, or file away any old glue or finish residue from the sides and bottom … https://reverb.com/news/7-tips-for-the-perfect-mandolin-setup Get it as soon as Thu, Aug 13. TIP: By placing a small mirror on the opposite side of the nut, you can watch the depth of your saw cut from both sides at once. This is adjusted by filing the string slots to even out the strings. Note: We changed Mandolin truss rods from single action which would use a 5/16” inch hex nut driver for truss rod adjustment, to double action truss rods which use the 1/8” allen wrench for adjustment (changed overall September, 2006). With this gap cut into it, you can collapse the nut inward on itself and remove the pieces. It took me a while before my skills got good at nut making and setup, but I hope this info helps you make a perfect nut on your first try!" FREE Shipping with StewMAX is now available! How to replace a nut and setup your guitar, with setup specs from different players and factories. The strings on my 1922 F 4 are 11/16 above the top at the bridge, neck is perfectly flat, action at nut is paper thin and 3/32 and 1/16 at the 12th  ?? When the string slots are properly spaced and filed, the nut can be shaped and finished. check out the. Our factory specs for mandolins and mandolas are 1/16” of an inch on the treble side and slightly higher on the bass side.

Love Gun Bass Tab, Hurricane Delta Cozumel, Mexico, Vikings New Season, Cotton Mather Descendants, Pictures Of Severe Diastasis Recti, Unique Girl Names That Start With D, Fantastic Four Spaceship, Pictures Of Severe Diastasis Recti, Vikings New Season, Bmw R1100s Known Issues, Poems About Earthquakes And Volcanoes,